7 Steps to Check Skid Steer Track Fit

Last Updated: November 19, 2026

Quick Summary

To check skid steer track fit, read the size code on your current track sidewall, then measure the track’s width, pitch, and link count and compare all three numbers. Confirm compatibility using your machine’s make, model, and serial number range, and verify the result against a track size chart.

  • A track size code like 450x86x56 gives track width, pitch, and link count.
  • Measure width at three points and average them, since a worn track can read narrow.
  • Mark your starting link with chalk when counting links around the full loop.
  • If the size chart and your measurements disagree, trust the measurements.
  • Never loosen a grease fitting with the track under pressure.
Not sure your track will fit?We verify fit by machine model and serial number before you order.

Request a Quote

Table of Contents

Step 1: Read the Track Size and Confirm Compatibility

Getting the right skid steer track fit starts with reading the numbers stamped on your current track. Every rubber track carries a size code molded into the sidewall, usually like 450x86x56, which tells you the track width, pitch, and link count.

Here is how to read it.

  • First number: track width in millimeters
  • Second number: pitch, or the distance between link centers in millimeters
  • Third number: total number of track links

Write those three numbers down first. If the sidewall is worn or dirty, scrub it clean and use a flashlight, a misread digit sends you down the wrong path.

Now confirm compatibility. The size code alone does not guarantee a fit; you also need your machine’s make, model, and serial number range. Manufacturers sometimes change the undercarriage mid-production, so two machines with the same model name can take different tracks. Check the machine manual or dealer parts lookup for your serial number.

Watch out: Never assume a track fits because the width matches. Width, pitch, and link count must all line up, or the track will not sit correctly on the undercarriage.

Step 2: Measure Skid Steer Tracks and Compare the Numbers

Measuring a skid steer track is simple once you know what to check. You need three measurements: overall width, pitch, and link count. Compare each to the size code from Step 1.

Contractor measuring the width of a rubber track to ensure a proper skid steer track fit on a job site
Contractor measuring the width of a rubber track to ensure a proper skid steer track fit on a job site

Width. Lay the tape across the flat face of the track, lug to lug. Measure at three points and average them, since a worn track can read slightly narrow.

Pitch. Measure the center-to-center distance between two adjacent links. Do this along the inner drive side, where the sprocket engages. Compare it to the second number in the code.

Link count. Count every link around the full loop. Mark your starting link with chalk so you do not lose your place. This is the measurement people get wrong most often.

If any number is off, stop. A mismatch means the wrong size, not just a loose or worn track. Recheck your counting first.

Here are the three measurements to take and how to get each one right.

Measurement How to measure Watch out for
Width Tape across flat face, lug to lug; average three points Worn track can read slightly narrow
Pitch Center-to-center distance between two adjacent links Measure along inner drive side where sprocket engages
Link count Count every link around the full loop Mark starting link with chalk; most often gotten wrong

Step 3: Use a Skid Steer Track Size Chart to Verify the Fit

A skid steer track size chart cross-references your machine model against the correct track dimensions. Use it as a second check, not a replacement for measuring.

Here is how to use one correctly.

  • Find your machine make and model
  • Note the serial number range, since specs change by build
  • Match the listed width, pitch, and link count to your measurements
  • Confirm the track code format matches your sidewall

If the chart and your measurements disagree, trust the measurements. Charts can lag behind manufacturer changes, and a previous owner may have re-tracked the machine with a different setup.

This is where a model-aware checklist pays off. Many guides skip serial number ranges entirely, and that gap is exactly where wrong-fit orders come from. When you buy replacement tracks, ask the supplier to confirm fit against your serial number, not just the model name.

Step 4: Check Skid Steer Track Tension Adjustment and Sag

Skid steer track tension adjustment controls how much the track sags between the front idler and the rear sprocket. Too loose and the track can derail. Too tight and you wear out bearings, idlers, and the track itself.

Here is the tension check.

  1. Park on level ground and lower the lift arms
  2. Shut off the machine and relieve hydraulic pressure
  3. Find the grease fitting on the tension cylinder
  4. Measure the gap between the track and the undercarriage at the midpoint
  5. Compare the sag to your machine manual’s spec

Sag specs vary by machine, so use your manual’s number, not a generic figure. Measure under the same conditions each time, ideally unloaded and cool.

Watch out: Never loosen a grease fitting with the track under pressure. Grease can release suddenly and cause injury. Follow the manual’s relief procedure exactly.

If the track will not hold tension, or sags again right after adjustment, the tension cylinder or a worn idler may be the cause. That is a repair issue, not a track-fit issue. Distinguishing the two saves you from replacing a good track.


A track that fits right and holds tension keeps your crew moving. If you are unsure whether a track will fit your machine, you can request a quote from North East Attachment and Track, and pricing depends on quantity, dates, and delivery.

Frequently Asked Questions

How do I know if a rubber track will fit my skid steer?

Match three numbers: track width, pitch, and link count, all stamped on the sidewall of the old track. Cross-check those against your machine’s manual and a size chart for your model. If any one of the three is off, the track will not seat correctly on the sprocket and idler, and you risk a derailed track or premature wear. Measure the old track yourself rather than trusting a parts listing alone.

How tight should skid steer tracks be?

Tension is set by sag, not by feel. Park on level ground, lift the frame so the track clears the ground, and measure the gap between the track and the undercarriage at the specified point. Your machine manual gives the acceptable range, which varies by model and track type. Too loose and the track can derail; too tight and you wear out the idler and sprocket. Always relieve grease pressure at the fitting before adjusting.

Can you use a different track size on a skid steer?

Only within the range the manufacturer approves for that machine. A wider track changes ground pressure and clearance, and a different pitch or link count will not mesh with your sprocket. Before buying, confirm width, pitch, and link count against the manual and verify with a size chart. If you are unsure, request a spec sheet from the supplier so the skid steer track fit is documented before installation.